1

Structure of control cable products

The structural elements of control cable products are generally divided into four main structural elements, namely, wires, insulating layers, shielding and protective layers, as well as filling elements and stretching elements. According to the use requirements and application conditions of the products, some products have extremely simple structures and are a structure of wires, such as overhead bare wires, contact network wires, copper-aluminum buses (busbars), etc, the external electrical insulation of these products is ensured by the spatial distance from the insulator (I. e. air insulation) during installation and laying. So, what is the structure of the control cable product, take a look!

Release time

2021-05-06

Measures to Prevent Interference of Control Cables

Control cable to prevent or reduce electrical interference measures mainly include the following three aspects. 1. A spare core wire of the control cable is grounded: practice has proved that when a spare core wire of the control cable is grounded, the amplitude of the interference voltage can be reduced to 25% ~ 50%, the implementation is simple, but the cable cost increases little. 2. When electrical interference occurs, the control cable is not suitable for circuits with serious consequences: including:(1) weak current signal control circuit and strong signal control circuit;(2) low-level signal and high-level signal loop;(3) In split-phase operation, the weak current control circuits of each phase of the AC circuit breaker should not use the same

Release time

2021-04-21

Mineral insulated power cable manufacturers

The characteristics of mineral insulated fireproof cable: 1. The mineral insulated fireproof cable produced by the mineral insulated power cable manufacturer (Shandong Yanggu Haohui Cable Co., Ltd.) has a high working temperature: the mineral fireproof cable can withstand continuous working temperature of up to 250 ℃. 2. The mineral insulated fireproof cable produced by the mineral insulated power cable manufacturer (Shandong Yanggu Haohui Cable Co., Ltd.) has fire resistance: the two materials used in the mineral fire-resistant cable, copper and magnesium oxide, are inorganic. The cable will not burn or support combustion, and can continue to run near the flame.

Release time

2021-04-07

Classification of wires and cables for electrical equipment

One of the five main types of wire and cable for electrical equipment. How to understand the basic knowledge of wires and cables for such electrical equipment is also important for our technicians and medium and high voltage cables.

Release time

2021-03-23

Measures to prevent wire and cable failure

Measures to prevent wire and cable failure

Through the analysis of the causes of insulation, accessories and outer sheath failures, it can be seen that the wire and cable project is a systematic project, and only the whole process management from the aspects of design, construction, operation and maintenance can ensure its safe operation to a large extent. From the beginning of the design, we fully understand the grounding system used in the wire and cable, and choose the cable that meets its voltage level to avoid the wire and cable working under long-term overvoltage conditions. The selection of the outer sheath should meet the requirements of the use environment and service life, and the selection of the cable sheath protector should meet the principle that the protector can reliably pass the grounding current without damage when it is relatively grounded.

Release time

2021-03-08

Discussion on Wire and Cable for Electrical Equipment

Wires and cables for electrical equipment include the direct transmission of electrical energy from the distribution points of the power system to electrical equipment, wires and cables with appliances as connecting wires, and various general or special wires and cables in measurement and signal control systems within electrical equipment.

Release time

2021-02-25

Maintenance of wire and cable

The service life of the wire and cable depends on the quality of the cable and the environment in which the cable is installed. This wire and cable is mainly insulated by an outer wrap. For a long time by corrosive gas corrosion, insulation performance gradually decreased, slowly aging hard, brittle or fall off. It is very dangerous for wires and cables to lose their insulation properties. If the two cables touch each other or the live wire touches something connected to the earth, there will be a power outage, which will increase the temperature of the local wires, generate sparks, and cause a fire. Therefore, please note that the wire and cable should not be damp, heated, corroded or scratched. Wire and cable use for a certain period of time should pay attention to inspection, found that there is a fault should be timely

Release time

2021-02-01

Low voltage power cable should pay attention to daily maintenance

What are the daily maintenance of low-voltage power cables? The use of electricity makes modern life develop rapidly. If the Yanggu cable is not used and maintained correctly, it may cause certain safety hazards, which may lead to accidents, especially fires. When using pumps and motors, cables are the main cables. In order to ensure safe construction and ensure the quality of Yanggu cable, we need to carry out the following maintenance on Yanggu cable: In order to ensure the construction quality, especially the production quality of Haohui cable head, the requirements must be strictly met. The cable tray shall be kept dry to prevent the cable from becoming damp, which may cause the insulation to fall off and cause a short circuit. Regularly clean the wires and Yanggu

Release time

2021-01-08

Why wire and cable maintenance

Wire and cable are used to transmit electrical energy (information), information and wire products for electromagnetic energy conversion. Wires and cables in a broad sense are also referred to as cables. A cable in the narrow sense refers to an insulated cable, which can be defined as: a collection consisting of the following parts; one or more insulated cores and their respective coatings, total protective layer and external protective layer, which can also make the cable have additional insulation. The vast majority of wire and cable products are products with exactly the same cross-sectional (cross-sectional) shape (ignoring manufacturing errors) and slender products. This is because it is used to form a circuit or coil in a determined system or device.

Release time

2021-01-04

Causes and treatment methods of water inflow of wires and cables

Wire and cable faults include water in the cable. Wire and cable water is a very tricky thing. So far, there is no effective way to solve it. The usual treatment method is the intermediate joint, and the other is to replace the entire wire and cable. The harm of water entering the wire and cable: In view of the fact that water enters the wire and cable, the damage is only a matter of time, and it will also cause damage to the cable. The effective method is to take preventive measures first. Next, let me introduce how to deal with the water in the wire and cable. The reason for the water ingress of the wire and cable: When the wire and cable are laid through the pipeline, the external insulation layer is broken and water penetrates into the cable. After laying wires and cables, two

Release time

2020-12-24

< 1...456...10 >